CIP Safety

System bezpieczeństwa – od linii produkcyjnej do pojedynczej maszyny

Szybkie, proste i elastyczne rozwiązanie, które pozwala zapewnić bezpieczeństwo na liniach produkcyjnych

1 wbudowany port EtherNet/IP (100Base-TX)
2 wbudowane porty z obsługą CIP-Safety przez EtherNet/IP
Do 254 połączeń bezpieczeństwa z NX-SL5700
Do 32 modułów we/wy NX na moduł sterujący komunikacji
Możliwy pakiet multicast
Możliwe rozwiązanie hybrydowe łączące sterownik NX1 z serią NX-SL5000

Modele i specyfikacja

Ordering Information

NX-series Communication Gateway Unit

Unit type	Appearance	Supported communications protocol	Number of communications connectors	Network variables	Unit version	Order code
Communication Control Unit		EtherNet/IP 2 Routing of the CIP Safety protocol is supported.	3	2 2 PORT1 is an independent port. PORT2A and PORT2B are the ports with a built-in Ethernet switch.	Ver. 1.01	NX-CSG320

Note:

One NX-END02 End Cover is provided with the NX-CSG320 Communication Control Unit.

NX-series Safety Control Units

Safety CPU Units

Unit type	Appearance	Specifications				Unit version	Order code
Unit type	Appearance	Maximum number of safety I/O points	Program capacity	Number of safety I/O connections	I/O refreshing method	Unit version	Order code
Safety CPU Unit (NX-SL5⬜⬜⬜)		1024 points	2048 KB	128	Free-Run refreshing	Ver. 1.3	NX-SL5500
Safety CPU Unit (NX-SL5⬜⬜⬜)		2032 points	4096 KB	254	Free-Run refreshing	Ver. 1.3	NX-SL5700

Note:

Refer to your local OMRON website for details of the NX-SL5⬜⬜⬜ Safety CPU Unit.

Safety Input Units

Unit type	Appearance	Specifications							Unit version	Order code
Unit type	Appearance	Number of safety input points	Number of test output points	Internal I/O common	Rated input voltage	OMRON special safety input devices	Number of safety slave connections	I/O refreshing method	Unit version	Order code
Safety Input Units		4 points	2 points	Sinking inputs (PNP)	24 VDC	Cannot be connected. 2 Various OMRON special safety input devices can be connected directly without a special controller. For detail of connectable OMRON special safety input devices, refer to NX-series User's Manual Safety Control Unit/Communication Control Unit (Cat. No. Z395).	1	Free-Run refreshing	Ver. 1.1	NX-SIH400
Safety Input Units		8 points	2 points	Sinking inputs (PNP)	24 VDC	Cannot be connected.	1	Free-Run refreshing	Ver. 1.0	NX-SID800

Safety Output Units

Unit type	Appearance	Specifications	Unit version	Order code
Safety Output Units		2 points	Sourcing outputs (PNP)	2.0 A/point, 4.0 A/Unit at 40°C, and 2.5 A/Unit at 55°C The maximum load current depends on the installation orientation and ambient temperature.	24 VDC	1	Free-Run refreshing	Ver. 1.0	NX-SOH200
	4 points	0.5 A/point and 2.0 A/Unit	NX-SOD400

Unit type

Appearance

Specifications

Unit version

Order code

Number of
safety output
points

Internal I/O
common

Maximum load current

Rated
voltage

Number of
safety slave
connections

I/O refreshing
method

Safety Output Units

2 points

Sourcing
outputs
(PNP)

2.0 A/point, 4.0 A/Unit at 40°C, and 2.5 A/Unit at 55°C

The maximum load current depends on the installation orientation and ambient temperature.

24 VDC

Free-Run refreshing

Ver. 1.0

NX-SOH200

4 points

0.5 A/point and 2.0 A/Unit

NX-SOD400

Automation Software Sysmac Studio

Please purchase a DVD and required number of licenses the first time you purchase the Sysmac Studio. DVDs and licenses are available individually. Each model of licenses does not include any DVD.

Product name	Specifications	Number of licenses	Media	Order code
Sysmac Studio Safety Edition Ver. 1.⬜⬜ 2 The Safety Edition can be used with the Communication Control Unit and EtherNet/IP Coupler Unit.	Sysmac Studio Safety Edition is a license including necessary setting functions for the safety control system. Note:This product is a license only. You need the Sysmac Studio Standard Edition DVD media to install it.	1 license	–	SYSMAC-FE001L
Sysmac Studio Standard Edition Ver. 1.⬜⬜ 2 The Sysmac Studio Standard Edition License (SYSMAC-SE2⬜⬜L) includes functions that the Safety Edition (SYSMAC-FE001L) provides. The Communication Control Unit can be used with the Sysmac Studio version 1.24 or higher.	The Sysmac Studio is the software that provides an integrated environment for setting, programming, debugging and maintenance of machine automation controllers including the NJ/NX-series CPU Units, NY-series Industrial PC, EtherCAT Slave, and the HMI. Sysmac Studio runs on the following OS. Windows 7(32-bit/64-bit version)/8(32-bit/64-bit version)/8.1(32-bit/64-bit version)/10(32-bit/64-bit version)	– (Media only)	DVD	SYSMAC-SE200D

Product name

Specifications

Number of licenses

Media

Order code

Sysmac Studio
Safety Edition
Ver. 1.⬜⬜

Sysmac Studio Safety Edition is a license including necessary setting functions for the safety control system.

Note:This product is a license only. You need the Sysmac Studio Standard Edition DVD media to install it.

1 license

–

SYSMAC-FE001L

Sysmac Studio
Standard Edition
Ver. 1.⬜⬜

The Sysmac Studio is the software that provides an integrated environment for setting, programming, debugging and maintenance of machine automation controllers including the NJ/NX-series CPU Units, NY-series Industrial PC, EtherCAT Slave, and the HMI.

Sysmac Studio runs on the following OS.

Windows 7(32-bit/64-bit version)/8(32-bit/64-bit version)/8.1(32-bit/64-bit version)/10(32-bit/64-bit version)

– (Media only)

DVD

SYSMAC-SE200D

Note:

For details of the Automation Software Sysmac Studio, refer to your local OMRON website.

Optional Products

Product name	Specifications	Order code
Memory Card	SD memory card, 2 GB	HMC-SD291
Memory Card	SD memory card, 4 GB	HMC-SD491
Unit/Terminal Block Coding Pins	For 10 Units (Terminal Block: 30 pins, Unit: 30 pins)	NX-AUX02

Product name	Specifications				Order code
Product name	No. of terminals	Terminal number indications	Ground terminal mark	Terminal current capacity	Order code
Terminal Block	8	A/B	Provided	10 A	NX-TBC082
	8	A/B	None	10 A	NX-TBA082
	16	A/B	None	10 A	NX-TBA162

Accessories

Communication Control Unit Accessories

Product name	Remark	Order code
End Cover	One End Cover is provided with the Communication Control Unit.	NX-END02

Specifications

Regulations and Standards

NX-series Safety Control Units

Certification body	Standards
TÜV Rheinland 2 The FSoE protocol was certified for applications in which OMRON FSoE devices are connected to each other. For compatibility with FSoE devices other than OMRON FSoE devices, the customer must validate FSoE communications.	EN ISO 13849-1EN ISO 13849-2IEC 61508 parts 1-7IEC/EN 62061IEC/EN 61131-2	IEC 61326-3-1IEC 61131-6 2 Only NX-SL5500/5700 have obtained IEC 61131-6 and FSPC certifications.
UL	NRAQ (UL61010-1, and UL 61010-2-201)NRAG (ANSI/ISA 12.12.01, or UL 121201)NRAQ7 (CSA C22.2 No. 61010-1, and CSA C22.2 No. 61010-2-201)FSPC (IEC 61508 and ISO 13849) 2 Only NX-SL5500/5700 have obtained IEC 61131-6 and FSPC certifications.

The NX-series Safety Control Units allow you to build a safety control system that meets the following standards.
- Requirements for SIL 3 (Safety Integrity Level 3) in IEC 61508, IEC/EN 62061, (Functional Safety of Electrical/Electronic/Programmable Electronic Safety-related Systems)
- Requirements for PLe (Performance Level e) and for safety category 4 in EN ISO13849-1

The NX-series Safety Control Units are also registered for RCM, EAC, and KC compliance.

NX-series Communication Control Unit

Certification body	Standards
UL	NRAQ (UL61010-1, and UL 61010-2-201)NRAG (UL 121201)

The NX-series Communication Control Units are also registered for RCM, EAC, and KC compliance.

General Specifications

Item		Specifications
Enclosure		Mounted in a panel (open)
Grounding method		Ground to 100 Ω or less
Operating environment	Ambient operating temperature	0 to 55°C
	Ambient operating humidity	10% to 95% (with no condensation or icing)
	Atmosphere	Must be free from corrosive gases.
	Ambient storage temperature	−25 to 70°C (with no condensation or icing)
	Altitude	2,000 m max.
	Pollution degree	2 or less: Conforms to JIS B3502 and IEC 61131-2.
	Noise immunity	Conforms to IEC 61131-2. 2 kV on power supply line
	Insulation class	Class III (SELV)
	Overvoltage category	Category II: Conforms to JIS B3502 and IEC 61131-2.
	EMC immunity level	Zone B
	Vibration resistance	Conforms to IEC 60068-2-6. 5 to 8.4 Hz with 3.5-mm amplitude 8.4 to 150 Hz, acceleration of 9.8 m/s² 100 minutes each in X, Y, and Z directions (10 sweeps of 10 min each = 100 min total)
	Shock resistance	Conforms to IEC 60068-2-27. 147 m/s², 3 times each in X, Y, and Z directions
	Insulation resistance 2 The specifications are for the Communication Control Unit, Safety Input Unit, and Safety Output Unit, not for the Safety CPU Unit.	20 MΩ between isolated circuits (at 100 VDC)
	Dielectric strength 2 The specifications are for the Communication Control Unit, Safety Input Unit, and Safety Output Unit, not for the Safety CPU Unit.	510 VAC for 1 min between isolated circuits, leakage current: 5 mA max.
Installation method		DIN Track (IEC 60715 TH35-7.5/TH35-15)

Communication Control Unit

Unit name		Communication Control Unit
Model		NX-CSG320
Indicators		[RUN] indicator, [ERROR] indicator, [BUSY] indicator, [SD PWR] indicator, [SD BUSY] indicator, [NS] indicator × 2, [L/A] indicator, [L/A 2A] indicator, [L/A 2B] indicator, [TS] indicator, [UNIT PWR] indicator, [I/O PWR] indicator
Hardware switch settings		[IP ADDRESS 1] Switch (x16, x1), [IP ADDRESS 2] Switch (x16, x1), DIP Switch Factory default IP ADDRESS1: 192.168.1.1 [IP ADDRESS 1] Switch = “00” IP ADDRESS2: 192.168.250.1 [IP ADDRESS 2] Switch = “00”
Dimensions 2 Includes the End Cover, and does not include projecting parts.		72 × 100 × 90 mm (W × H × D)
Weight 2 Includes the End Cover. The weight of the End Cover is 82 g.		390 g
Number of NX Units that you can connect		32 units or less
Number of communications that can be set between NX Units		254 ports max. 2 Includes the SD Memory Card. The NX Unit power consumption to NX Units is not included.
Unit power supply	Power supply voltage	24 VDC (20.4 to 28.8 VDC)
	Unit power consumption 2 This is the inrush current value when the power supply turns ON after it has been OFF. The inrush current may vary depending on the operating condition and other conditions. Therefore, select fuses, breakers, and external power supply devices that have enough margin in characteristic and capacity, considering the condition under which the devices are used. Especially when you turn the power ON/OFF through a switch inserted to the external DC power supply, cycling power ON-OFF-ON within one second will cause the inrush current of approx. 30 A/0.3 mA to occur since the inrush current limiter circuit fails to limit the current.	5.95 W
	Inrush current 2 The amount of current that can be passed constantly through the terminal. Do no exceed this current value when you use a through-wiring for the Unit power supply.	For cold start at room temperature: 10 A max./0.1 ms max. and 2.5 A max./150 ms max.
	Current capacity of power supply terminal 2 The actual configurable number can be calculated as follows: 254 - <Number of CIP Safety connections configured> - <Number of FSoE connections configured>	4 A
	Isolation method	No isolation: Between the Unit power supply terminal and internal circuit
Power supply to the NX Unit power supply	NX Unit power supply capacity	10 W max.
	NX Unit power supply efficiency	80%
	Isolation method	No isolation: Between the Unit power supply terminal and NX Unit power supply
I/O power supply to NX Units	Power supply voltage	5 to 24 VDC (4.5 to 28.8 VDC)
	Maximum I/O power supply current	4 A
Current consumption from I/O power supply		10 mA max. (24 VDC)
External connection terminals		Screwless clamping terminal block (8 terminals)
Terminal connection diagram		UV/UG: Unit power supply terminals IOV/IOG: I/O power supply terminals
Accessories		End cover (NX-END02): 1 pc.
Installation orientation and restrictions		Only upright installation orientation

Built-in EtherNet/IP Port Specifications

The following table shows the specifications of the built-in EtherNet/IP port of the Communication Control Unit.

Item		Specifications
Item		NX-CSG-⬜⬜⬜
Communications protocol		TCP/IP or UDP/IP
Supported services		Sysmac Studio connection, tag data links, CIP message communications, FTP server, automatic clock adjustment (NTP client), SNMP (agent), DNS (client), BOOTP (client), TCP/UDP message service
Number of logical ports		2 (With IP routing function)
Physical layer		100Base-TX or 10Base-T (100Base-TX is recommended.) 2 If tag data links are being used, use 100Base-TX.
Transmission specifications	Media access method	CSMA/CD
	Modulation	Baseband
	Transmission paths	Star form
	Baud rate	100 Mbps (100BASE-TX)
	Transmission media	Shielded twisted-pair (STP) cable, Category 5, 5e or higher
	Transmission distance	100 m max. (distance between hub and node)
	Number of cascade connections	The built-in switching ports support up to 50 nodes. There is no limitation when an external Ethernet switch is used.
CIP Safety routing	Maximum number of routable CIP Safety connections	254 total For multi-cast connections, 128 total
CIP Safety routing	Maximum routable Safety data length per connection	32 bytes
CIP service: Tag data links (cyclic communications)	Number of connections	32/Logical ports (total of 64 with two logical ports)
	Packet interval (refresh cycle)	1 to 10,000 ms in 1-ms increments
	Packet interval (refresh cycle)	Packet intervals can be set independently for each connection. (Data is refreshed over the network at preset intervals and does not depend on the number of nodes.)
	Allowed communications bandwidth per Unit	12,000 pps 2 Here, pps means “packets per second” and indicates the number of packets that can be processed in one second. Note:The heartbeat and CIP Safety routing are included.
	Number of registrable tags	1024/Logical ports (total of 2048 with two logical ports)
	Tag types	Network variables
	Number of tags per connection (=1 tag set)	32 (31 tags if Controller status is included in the tag set.)
	Maximum link data size per node	46,208 bytes/Logical ports 92,416 bytes total
	Maximum data size per connection	1,444 bytes 2 To use a data size of 505 bytes or higher, the system must support a large forward open (an optional CIP specification). The CS, CJ, NJ, and NX-series Units support a large forward open, but before connecting to nodes of other companies, confirm that those devices also support it.
	Number of registrable tag sets	Data concurrency is maintained within each connection.
	Number of registrable tag sets	32 per port (1 connection = 1 tag set) (total of 40 with two logical ports) 2 If more than 40 tag sets are registered in total, the Tag Data Link, Too Many Tag Sets Registered (840E0000 hex) event will occur.
	Maximum size of 1 tag set	1,444 bytes (Two bytes are used if Controller status is included in the tag set.)
	Multi-cast packet filter 2 Because the built-in EtherNet/IP port is equipped with an IGMP client (version 2), unnecessary multicast packets can be filtered out by an Ethernet switch that supports IGMP Snooping.	Supported.
CIP message service: Explicit messages 2 The built-in EtherNet/IP port uses the TCP/UDP port numbers shown in the following table. Do not set the same port number for more than one TCP/UDP service.	Class 3 (number of connections)	Connections: 16/Logical ports (total of 32 with two logical ports) (server only)
	UCMM (unconnected)	Maximum number of clients that can communicate at one time: 16 per port (total of 32 with two logical ports)Maximum number of servers that can communicate at one time: 16 per port (total of 32 with two logical ports)
TCP/UDP message service	Maximum number of clients that can communicate at one time	16 per port (total of 32 with two logical ports)
TCP/UDP message service	Maximum message size	Request: 492 bytes Response: 496 bytes
SNMP	Agent	SNMPv1, SNMPv2c
SNMP	MIB	MIB-II
EtherNet/IP conformance test		Conforms to CT14
Ethernet interface		10BASE-T or 100BASE-TX Auto negotiation or fixed settings

Used TCP/UDP port numbers

Do not set the same port number for more than one TCP/UDP service.

Service	Type	Port number	Remarks
Tag data links	UDP	2222	Fixed values
Used by system	UDP	2223, 2224
Used by system	TCP	9610
CIP messages	TCP	44818
FTP client (Data transfer port)	TCP	20
DNS client	TCP/UDP	53
BOOTP client	UDP	68
HTTP server	TCP	80
Used by system, other	TCP/UDP	9600	You can change the port number in the Unit Settings on the Sysmac Studio.
FTP client (Control port)	TCP	21
TCP/UDP message service	TCP/UDP	64000
NTP client	UDP	123
SNMP agent	UDP	161
SNMP trap	UDP	162

Safety Control Units

Safety CPU Units NX-SL5500/SL5700

Unit name	Safety CPU Unit
Model	NX-SL5500	NX-SL5700
Maximum number of safety I/O points	1024 points	2032 points
Program capacity	2048 KB	4096 KB
Number of safety master connections 2 This is the maximum number of Safety I/O connections that can be set to this Unit. The value is the total number of CIP Safety originator connections, CIP Safety target connections, and FSoE master connections.	128	254
Number of CIP Safety originator connections	128	254
Number of CIP Safety target connections	4	4
Number of originators that can be connected with a multi-cast connection	8	8
Number of FSoE master connections	128	254
I/O refreshing method	Free-Run refreshing
External connection terminals	None
Indicators	[TS] indicator, [NS] indicator, [FS] indicator, [P ERR] indicator, [RUN] indicator, [VALID] indicator, [DEBUG] indicator, seven-segment indicator	[TS] indicator, [NS] indicator, [FS] indicator, [P ERR] indicator, [RUN] indicator, [VALID] indicator, [DEBUG] indicator, seven-segment indicator
Hardware switch settings	[SERVICE] switch, [SETTING] switch	[SERVICE] switch, [SETTING] switch
Dimensions	30 × 100 × 71 mm (W × H × D)
I/O power supply method	Not supplied.
Current capacity of I/O power supply terminals	No I/O power supply terminals
NX Unit power consumption	3.35 W max. 2 The cable length for the Units (Communication Control Unit and Power Supply Unit for NX Units) that supply power to the corresponding Unit must be up to 20 m.
Current consumption from I/O power supply	No consumption
Weight	130 g max.
Installation orientation and restrictions	Installation orientation: Upright installation Restriction 2 Only NX102 CPU Units and Communication Control Units can be connected. NX1P2 CPU Units or Communications Coupler Units cannot be connected. : None.

Safety Input Units NX-SIH400/SID800

Unit name	Safety Input Unit
Model	NX-SIH400	NX-SID800
Number of safety input points	4 points	8 points
Number of test output points	2 points	2 points
Internal I/O common	PNP (sinking inputs)
Rated input voltage	24 VDC (20.4 to 28.8 VDC)
OMRON special safety input devices	Can be connected.	Cannot be connected.
Number of safety slave connections	1
I/O refreshing method	Free-Run refreshing
External connection terminals	Screwless clamping terminal block (8 terminals)	Screwless clamping terminal block (16 terminals)
Indicators	[TS] indicator, [FS] indicator, [IN] indicator, [IN ERR] indicator	[TS] indicator, [FS] indicator, [IN] indicator, [IN ERR] indicator
Safety input current	4.5 mA TYP.	3.0 mA TYP.
Safety input ON voltage	11 VDC min.	15 VDC min.
Safety input OFF voltage/OFF current	5 VDC max., 1 mA max.
Test output type	Sourcing outputs (PNP)
Test output load current	25 mA max.	50 mA max.
Test output residual voltage	1.2 V max. (Between IOV and all output terminals)
Test output leakage current	0.1 mA max.
Dimensions	12 × 100 × 71 mm (W × H × D)
Isolation method	Photocoupler isolation
Insulation resistance	20 MΩ min. between isolated circuits (at 100 VDC)
Dielectric strength	510 VAC for 1 min between isolated circuits, leakage current: 5 mA max.
I/O power supply method	Power supplied from the NX bus
Current capacity of I/O power supply terminals	No applicable terminals.
NX Unit power consumption	Connected to a CPU Unit or a Communication Control Unit 1.10 W max.Connected to a Communications Coupler Unit 0.70 W max.	Connected to a CPU Unit or a Communication Control Unit 1.10 W max.Connected to a Communications Coupler Unit 0.75 W max.
Current consumption from I/O power supply	20 mA max.
Weight	70 g max.
Circuit layout
Terminal connection diagram	Si0 to Si3: Safety input terminals T0 and T1: Test output terminals Refer to User's manual (Cat. No. Z395) for details.	Si0 to Si7: Safety input terminals T0 and T1: Test output terminals Refer to User's manual (Cat. No. Z395) for details.
Installation orientation and restrictions	Installation orientation: Connected to a CPU Unit or a Communication Control Unit 2 Only NX102 CPU Units and Communication Control Units can be connected. NX1P2 CPU Units cannot be connected. Possible in the upright installation orientation. Connected to a Communications Coupler Unit 6 possible orientations. Restrictions: Maximum ambient temperature is 50°C for any orientation other than upright installation.
Protective functions	Overvoltage protection circuit and short detection (test outputs)

Safety Output Units NX-SOH200/SOD400

Unit name	Safety Output Unit
Model	NX- SOH200	NX- SOD400
Number of safety output points	2 points	4 points
Internal I/O common	PNP (sourcing outputs)
Maximum load current	2.0 A/point 4.0 A/Unit at 40°C 2.5 A/Unit at 55°CThe maximum load current depends on the installation orientation and ambient temperature	0.5 A/point and 2.0 A/Unit
Rated voltage	24 VDC (20.4 to 28.8 VDC)
Number of safety slave connections	1
I/O refreshing method	Free-Run refreshing
External connection terminals	Screwless clamping terminal block (8 terminals)
Indicators	[TS] indicator, [FS] indicator, [OUT] indicator, [OUT ERR] indicator	[TS] indicator, [FS] indicator, [OUT] indicator, [OUT ERR] indicator
Safety output ON residual voltage	1.2 V max. (Between IOV and all output terminals)
Safety output OFF residual voltage	2 V max. (Between IOG and all output terminals)
Safety output leakage current	0.1 mA max.
Dimensions	12 × 100 × 71 mm (W × H × D)
Isolation method	Photocoupler isolation
Insulation resistance	20 MΩ min. between isolated circuits (at 100 VDC)
Dielectric strength	510 VAC for 1 min between isolated circuits, leakage current: 5 mA max.
I/O power supply method	Power supplied from the NX bus
Current capacity of I/O power supply terminals	IOG: 2 A max./terminal	IOG (A3 and B3): 2 A max./terminal IOG (A7 and B7): 0.5 A max./terminal
NX Unit power consumption	Connected to a CPU Unit or a Communication Control Unit 1.05 W max. Connected to a Communications Coupler Unit 0.70 W max.	Connected to a CPU Unit or a Communication Control Unit 1.10 W max. Connected to a Communications Coupler Unit 0.75 W max.
Current consumption from I/O power supply	40 mA max.	60 mA max.
Weight	65 g max.
Circuit layout
Terminal connection diagram	So0 and So1: Safety output terminals IOG: I/O power supply 0 V Refer to User's manual (Cat. No. Z395) for details.	So0 to So3: Safety output terminals IOG: I/O power supply 0 V Refer to User's manual (Cat. No. Z395) for details.
Installation orientation and restrictions	Installation orientation: Connected to a CPU Unit or a Communication Control Unit 2 Only NX102 CPU Units and Communication Control Units can be connected. NX1P2 CPU Units cannot be connected. Possible in the upright installation orientation. Connected to a Communications Coupler Unit 6 possible orientations. Restrictions: For upright installation, the ambient temperature is restricted as shown below depending on the total Unit load current. For all installation orientations other than upright installation, the ambient temperature is restricted as shown below according to the total Unit load current.	Installation orientation: Connected to a CPU Unit or a Communication Control Unit 2 Only NX102 CPU Units and Communication Control Units can be connected. NX1P2 CPU Units cannot be connected. Possible in the upright installation orientation. Connected to a Communications Coupler Unit 6 possible orientations. Restrictions: None
Protective functions	Overvoltage protection circuit and short detection (test outputs)

Jak możemy Ci pomóc?

W razie pytań lub chęci przesłania prośby o wycenę skontaktuj się z nami lub wyślij zlecenie.

+48 22 458 6666

Zapytaj o ofertę

Oferta dla CIP Safety

Poniżej możecie Państwo wysłać zapytanie cenowe dotyczące naszych produktów. Prosimy wypełnić wszystkie pola oznaczone *. Twoje dane osobowe będą oczywiście traktowane jako poufne.

Dane osobowe

Produkt CIP Safety

Imię.

Text error notification

Nazwisko

Text error notification

Adres e-mail

Email error notification

Telefon

Text error notification

Firma

Text error notification

Kraj

Country error notification

Szczegóły oferty

Kupujesz od firmy Omron czy od dystrybutora/partnera?

Select notification error

Tytuł/stanowisko

Select notification error

Pytania i uwagi

Text area error notification

Zgadzam się z OMRON Privacy Policy

Checkbox error notification

Subskrybuj biuletyn

Checkbox error notification

Dziękujemy za zlecenie wyceny. Dostarczymy Ci niezbędnych informacji tak szybko, jak to tylko będzie możliwe.

Problem techniczny. Akcja nie została wykonana. Przepraszamy - spróbuj ponownie.

Download

Zapytaj o ofertę

Filmy

Omron NX-Series Safety Network Controller

NX Series CIP Safety Controller with EtherCAT and Ethernet/IP capabilities. In addition to new hardware, Sysmac Studio new functions include Automatic Programming, Safety Data Logging, and Online Functional Test. For more information visit: USA Canada Mexico

Powiązane produkty

NX Safety Hybrid

Od pojedynczej maszyny do całej linii produkcyjnej – kompletny system bezpieczeństwa
NX Safety – wersja do systemów rozproszonych

Zabezpieczenia zintegrowane z automatyką przemysłową
Seria GI-S

Seria GI-S
Seria modułów we/wy NX

Wydajność i funkcjonalność sterowania maszyną